Naples and Southwest Florida

How we work

Naples Top Tech takes home technology from consultation through design, installation, programming, homeowner training and ongoing support.

We work with homeowners, builders, architects and designers. The starting point is how the home should work: the rooms you use, the systems you need and the decisions construction requires. Equipment selection follows that discussion.

Founded in 2017, NTT is a Control4, Lutron and Vantage dealer serving Naples, Bonita Springs, Estero, Fort Myers and Marco Island.

What happens at each stage of the project?

1. What do we cover in the first conversation?

We discuss your priorities, current problems and project stage. Tell us whether you are building, renovating or improving an existing home. Plans, equipment photos and a list of the functions you want help define the next step.

2. What do we learn during the on-site assessment?

We review the spaces and systems within the proposed scope. That includes accessible wiring, equipment locations, network coverage, power needs and the way existing controls behave. Site conditions establish what can stay, what needs further testing and where installation access matters.

3. How do design and the proposal come together?

We translate your priorities into a coordinated system design and written scope. The proposal identifies equipment, installation, programming, training and documentation, along with assumptions and work assigned to other trades. You review the scope and options before authorizing the work.

4. When does pre-wire happen during construction?

Technology planning starts before rough-in. Cable installation is coordinated with the builder while the required routes remain accessible, ahead of insulation and wall or ceiling closure. We plan the agreed connections for networking, audio/video, cameras, shades and controls, then label and check the installed wiring.

5. What happens during trim and installation?

After the relevant finishes and mounting locations are ready, we terminate connections and install the specified equipment. TVs, speakers, controls, shades and network equipment follow the approved layout. Rack organization, ventilation and service access remain part of the installation plan.

6. What does programming actually do?

Programming gives supported equipment its intended behavior. We set up room names, controls, lighting scenes, shade groups and audio/video functions within the agreed scope. Testing follows the action through to the physical result: the light changes, the shade moves or the correct source plays.

7. What happens during the walkthrough and training?

We demonstrate the everyday tasks you will use: operating a room, choosing a scene, playing music and finding the right control. You try those functions on the installed interfaces. We record remaining questions and agreed adjustments for follow-up.

8. What information is covered at handoff?

Handoff covers the documentation agreed in the proposal, such as equipment information, room and circuit labels, control descriptions and operating guidance. We review homeowner account access and explain how to request help. Configuration backups and technical records follow the capabilities of the installed systems and the agreed documentation scope.

9. How does support work after installation?

Start with the affected room, device and symptom when you contact us. The next step depends on the equipment, access and issue: remote diagnosis, a site visit or a proposed change. Maintenance coverage and response commitments belong in the applicable service agreement.

Low-voltage boxes mounted in open wall framing
In progress · rough-in

How does the process work for builders, architects and designers?

We bring technology decisions into the design and construction sequence. Keypad locations, ceiling speakers, shade pockets, display mounting and equipment space need coordination with lighting plans, finishes and millwork.

The project scope identifies the boundaries between low-voltage work, electrical work and other trades. Layout changes are reviewed for their effect on wiring, equipment, programming and timing. A clear decision before rough-in can prevent a difficult change after finishes are complete.

How does the process change in an existing home?

An existing home starts with what is installed and how well it works. We assess wiring, equipment, programming access and the practical routes for new connections. Compatible components can remain when their condition and specifications fit the plan.

NTT has completed in-place upgrades and conversions between automation or lighting-control brands. An upgrade plan identifies what stays, what changes and how the transition affects daily use. Where the system supports phases, we plan the sequence before disconnecting existing controls.

What else should you know about the process?

Do I need to choose a system before contacting NTT?

No. Start with what you want the home to do and what is difficult today. The assessment and design discussion establish which systems fit those needs.

Can I change the scope after approving the proposal?

Changes need a review of equipment, labor, programming and schedule effects. The revised scope is agreed before the added or changed work proceeds.

How long will the project take?

Timing depends on the scope, site access, equipment availability and construction readiness. The schedule is developed around those conditions and the other work taking place at the home.

Ready to plan your project?

Call (239) 300-0652 or request a consultation. Tell us where the project stands and what you want the home to do. Office hours are Monday–Friday, 8 AM–5 PM.

Why Naples Top Tech

  • We're local. We started in Naples in 2017.
  • We're a Control4, Lutron and Vantage dealer.
  • We design it, wire it, program it, and we're here after you move in.
  • We give you a clear proposal before work starts.
Plan your project

Tell us what you'd like to improve.